Contact

Reserved Technical Equipment (Vyhradené Technické Zariadenie)

Glossary Definition

Reserved technical equipment (vyhradené technické zariadenie) is pressure, lifting, electrical or gas equipment that Slovak safety law ranks as high or higher risk and therefore subjects to mandatory tests and periodic inspections. Decree 508/2009 sorts such equipment into groups A, B and C, and groups A and B are reserved. In a warehouse or factory that covers cranes above 1,000 kg, lifts, the transformer station and larger gas appliances. The party that operates the equipment must keep it tested and documented.

What reserved technical equipment is

Decree 508/2009 of the Slovak Ministry of Labour, which we read in the text in force since 1 September 2014, applies to four families of technical equipment: pressure, lifting, electrical and gas (section 2(1)). Section 4 divides each family by the degree of danger. Group A holds equipment with a high degree of danger, group B equipment with a higher degree and group C equipment with a lower degree. Section 4(2) then gives the definition in one sentence: equipment in group A and group B counts as reserved technical equipment.

The legal anchor sits one level up, in the Occupational Safety and Health Act 124/2006. Its section 13(3), in the text in force since 1 July 2025, lets an employer use buildings and operate work equipment only after the maintenance, inspections, tests, official tests and professional inspections required by special regulations have been carried out. The Decree is that special regulation. The term therefore describes a legal status, not a product category. The same overhead crane is ordinary machinery in a catalogue and a regulated item from the moment it is installed in a hall where people work. The classification follows the technical parameters, never the owner’s own view of the risk.

Which equipment in a hall falls into groups A and B

Annex 1 of the Decree lists the types. For lifting equipment, group A includes powered cranes and hoists with a capacity above 1,000 kg, mobile elevating work platforms with a lifting height above 1.5 m, lifts that are a permanent part of a building, and stacker cranes with an operator’s station. Group B includes powered cranes and hoists up to 1,000 kg, the lifting mechanism of an industrial truck used with slings, powered vertical sliding gates with a lifting height above 2.7 m, and stacker cranes without an operator’s station unless they are part of an automated handling and storage system.

For electrical equipment, group A covers transformation with an input of 250 kVA or more, networks above 1,000 V alternating current, and installations in rooms with a fire risk from flammable materials or with an explosion risk. Every other electrical installation with an unsafe current or voltage is in group B, which in practice means the whole wiring of a hall. For gas, group A includes appliances that burn gas with an output above 0.5 MW and refrigeration with more than 25 kg of gas. Stationary pressure vessels and boilers are classed by pressure, volume and output. A modern logistics building therefore rarely contains fewer than three families of reserved technical equipment.

Official tests, professional inspections and who performs them

Section 9 of the Decree names two levels of control. The official test (úradná skúška) and the repeated official test are carried out by an authorised legal entity, which is a body holding an authorisation from the National Labour Inspectorate under section 14 of Act 124/2006. The professional inspection and professional test (odborná prehliadka a odborná skúška) are carried out by a revision technician, an individual with a certificate for the relevant equipment (section 16).

Under section 12, group A equipment needs an official test before it goes into operation, after installation at its place of use and after any reconstruction. The authorised legal entity issues a certificate within 30 days of the test. Section 9(2) adds the occasions on which the safety of equipment must be checked again: before first use, before a restart after a shutdown of more than one year, after dismantling and reassembly, after reconstruction and repair, and during operation at least at the prescribed intervals. The result of every professional inspection is a written report. It states whether the equipment is fit for further operation and lists the defects that must be removed, so a report is not automatically a clean bill of health.

Intervals for reserved technical equipment in operation

The intervals sit in the annexes, and they differ sharply by type. Annex 7 covers lifting equipment. A powered crane above 1,000 kg needs a repeated official test every 10 years, a professional inspection every 2 years and a professional test every 4 years. For permanent crane runways and for cranes in a hot or aggressive environment, those two periods shorten to 1 year and 2 years. A lift that carries people needs a repeated official test every 6 years, a professional inspection every 3 months and a professional test every 3 years. A powered crane up to 1,000 kg in group B is inspected every 3 years and tested every 6 years.

Annex 8 covers electrical installations. It sets intervals between six months and five years, depending on the type of building and on the external influences recorded for each room, and the shorter of two applicable periods always counts. Section 12(2) adds a repeated official test at least every 10 years for group A electrical equipment. All of these periods are maximums: they apply unless the manufacturer’s technical conditions prescribe shorter ones. For an occupier, the practical result is a calendar with dozens of dates. In our experience the dates are rarely missed on the crane, and far more often on gates and on the wiring of mezzanines added later.

Who is responsible in a leased building

The Decree speaks of the operator (prevádzkovateľ): the employer or self-employed person who uses the equipment to perform their tasks (section 8). The operator keeps the accompanying technical documentation with all inspection and test records, keeps a register of the reserved equipment, issues a local operating rule for group A equipment where needed, and arranges the checks under section 9. Ownership is not the test. A tenant who runs a crane that belongs to the landlord is its operator, and the tenant’s employees are the ones the rules protect.

A lease should therefore say, item by item, who operates what. Building equipment such as lifts, the transformer station, the gas boiler room and the lightning protection usually stays with the landlord and is recharged through the service charge. Process equipment such as cranes, stacker cranes and charging stations usually sits with the tenant. The current reports belong in the handover protocol at the start and at the end of the lease. They also matter to the building office: under section 66 of the Building Act 25/2025, the results of measurements and inspections of this equipment are attached to the application, and the inspection checks that its operation is smooth and safe. Our blog shows where these reports matter when a warehouse is converted into a factory. Read it here: what the building office asks for.

Frequently Asked Questions

Is every machine in a factory reserved technical equipment?

No. Only pressure, lifting, electrical and gas equipment in groups A and B of Annex 1 to Decree 508/2009 has that status. Group C equipment and ordinary production machines follow general work equipment rules and the manufacturer’s instructions.

Who may carry out the inspections?

Official tests are reserved for an authorised legal entity holding an authorisation from the National Labour Inspectorate. Professional inspections and tests are done by a revision technician with a certificate for the specific type and group of equipment.

What happens after a long shutdown?

Equipment that stood idle for more than one year must be checked again before it is restarted (section 9(2)). The same applies after dismantling and reassembly and after a reconstruction or repair, which is relevant when a tenant takes over a hall that stood empty.

Does a valid report transfer to a new tenant?

The report describes the equipment, so it remains valid for its period. The new operator, however, takes over the duty to keep the documentation and the register, and should ask for all reports and certificates at handover.

Taking over a Slovak hall with cranes, lifts or its own transformer? Send us the equipment list, and we will check with you which reports the lease should hand over.

See Also

Turn vision into reality.

Tell us what you are looking for: a unit, a building, land or a development partner.

I’m interested in